This page shows how to change the LAN IP Address on the Sterlite SAM300AX router.
Other Sterlite SAM300AX Guides
This is the ip address guide for the Sterlite SAM300AX. We also have the following guides for the same router:
- Sterlite SAM300AX - Reset the Sterlite SAM300AX
- Sterlite SAM300AX - Sterlite SAM300AX Login Instructions
- Sterlite SAM300AX - How to change the DNS settings on a Sterlite SAM300AX router
- Sterlite SAM300AX - Information About the Sterlite SAM300AX Router
- Sterlite SAM300AX - Sterlite SAM300AX Screenshots
What is the LAN IP Address of a Router
The LAN IP Address of a router is also known as its internal IP address. It is also the IP address that you connect to when you want to configure your router. It is only useful from inside your network and has no use from the Internet side.
Routers have 2 IP addresses: an internal ip address and an external ip address. The external IP address is assigned to you by your Internet Service Provider, or ISP, and is generally not something that you can change. The internal IP address is set to a default value at the factory but can be changed if you want.
Common internal IP addresses for routers are:
- 192.168.0.1
- 192.168.1.1
- 10.0.0.1
It is generally a good idea to make the last number of your router's internal IP address a '1', as in 192.168.0.1 or 10.0.0.1. This is not necessary, but many people do it and it makes it a bit easier to remember which IP address is assigned to your router. If you want to change the internal IP address of your router, this guide shows you how.
Login To The Sterlite SAM300AX
To get started configuring the Sterlite SAM300AX LAN page you need to login to your router. If you are already logged in you can skip this step.
To login to the Sterlite SAM300AX, follow our Sterlite SAM300AX Login Guide.
Change the LAN IP Address on a Sterlite SAM300AX
If you followed our login guide above then you should see this screen.
Once you have logged into the Sterlite SAM300AX you see the Status page of the Router. When you need to change your Router IP Address, the address you see while inside your private network, click the choice at the top labeled Interface Setup, then LAN.
Configure the LAN section of your Sterlite SAM300AX
Here, you need to place your cursor in the box labeled IP Address and enter your new address you have chosen for your Router. We recommend using an address such as 192.168.1.1
While doing this, be sure to leave the IP Subnet Mask at 255.255.255.0
When you are done, click Save.
Possible Problems when Changing your LAN IP Address
When you change your LAN IP Address you are making a fundamental change to how your network functions and all computers on your network will be affected. You will lose your Internet connection when you apply these changes. Your router may reboot and require a couple of minutes to start responding again.
Also note that some computers may need to be rebooted after you make this change before they can talk to the router or on the Internet again.
Other Sterlite SAM300AX Info
Don't forget about our other Sterlite SAM300AX info that you might be interested in.
This is the ip address guide for the Sterlite SAM300AX. We also have the following guides for the same router:
- Sterlite SAM300AX - Reset the Sterlite SAM300AX
- Sterlite SAM300AX - Sterlite SAM300AX Login Instructions
- Sterlite SAM300AX - How to change the DNS settings on a Sterlite SAM300AX router
- Sterlite SAM300AX - Information About the Sterlite SAM300AX Router
- Sterlite SAM300AX - Sterlite SAM300AX Screenshots