Setup Router logo in white Setup router name logo in white
Get Software

How to Reset the Dlink DAP-1555-Bridge-Mode

Thumbnail image of Setup Router Staff
Setup Router Staff
(Last Updated: ) | Reading Time: 3 minutes

With this guide I explain how to reset the Dlink DAP-1555-Bridge-Mode router back to it's original factory defaults. Before we begin you must know the difference between a reset and a reboot. When you reboot a router you cycle the power to the device by turning it off and back on again. A router reset takes every single setting and returns it to factory defaults.

Warning: This router reset is a big problem solving step. Don't take a factory reset lightly. Problems arise when you don't fully understand what it will do. Making a list of settings you have changed is helpful. Consider the following before you reset your router:

  • The reset interface username and password are reverted to factory defaults.
  • The Internet name and password are also reverted to factory settings.
  • If this is a DSL router you need to re-enter the Internet Service Provider or ISP username and password. Call your ISP for more details.
  • If you have ever made any other changes to your router such as port forwards or IP address changes these are erased.

Other Dlink DAP-1555-Bridge-Mode Guides

This is the reset router guide for the Dlink DAP-1555-Bridge-Mode. We also have the following guides for the same router:

Reset the Dlink DAP-1555-Bridge-Mode

Use a VPN Instead

Have you considered using a VPN instead of forwarding a port? For most users, a VPN is a much simpler and more secure choice than forwarding a port.

We use and recommend NordVPN because not only is it the fastest VPN, it includes a new feature called Meshnet that makes forwarding a port no longer necessary for most applications. With NordVPN Meshnet, you can connect to your devices from anywhere in the world, completely secure, over a highly encrypted VPN tunnel.

When shopping for a VPN, make sure that they meet the following criteria:

  • Your VPN provider should have a no-logs policy. This means that they do not keep any logs of any kind.
  • Make sure that your VPN provider has lots of exit nodes all around the world.
  • Check that your VPN will not affect your speed.
  • Verify that your VPN provider uses WireGuard as the underlying protocol.
  • Many people prefer a VPN provider that is not based in the United States.

This is the list of requirements that we used when we were shopping around for a VPN provider. There are lots of free, shady VPN providers out there that we looked at and dismissed.

Based in Panama, using diskless servers, and with over 6,100 servers in 61 countries, we can safely say that NordVPN satisfies all of these requirements.

NordVPN is the fastest VPN!

Once you've set up your NordVPN account on multiple computers and enabled Meshnet, you can seamlessly access all of your devices as if they were on the same network. You don't even have to log in to your router. It's very simple.

Every time you click on one of our affiliate links, such as NordVPN, we get a little kickback for introducing you to the service. Think of us as your VPN wingman.

The first step in any reset is to locate the reset button. On this Dlink router it is found on the back panel. I have circled it's location for you in the image below.

router reset factory settings
This is the reset page from your Dlink DAP-1555-Bridge-Mode router.

Take an unfolded paperclip and press down on the reset button for about 10 seconds. This will begin the reset process which could take over a minute to complete. If you don't hold the reset button down for long enough you may end up only rebooting the router instead of resetting it causing confusion.

Remember this reset erases every setting you have ever made to your router. We recommend trying other troubleshooting methods first to try and avoid a reset.

Login to the Dlink DAP-1555-Bridge-Mode

Now that you've reset the Dlink DAP-1555-Bridge-Mode router you'll need to log into it. This is done using the factory default username and password. Don't know what these are? We have them listed for you in our Login Guide.

Tip: If the defaults aren't working it could be because you didn't hold the reset button down for long enough.

Change Your Password

Once you've logged in we suggest setting a new password. This can be anything you want, however bear in mind that a strong password is 14-20 characters in length and avoids any use of personal information. For more helpful hints be sure to visit our Choosing a Strong Password Guide.

Tip: To keep from losing your new password try writing it on a sticky note and attaching it to the underside of your router.

Setup WiFi on the Dlink DAP-1555-Bridge-Mode

You should also check on the WiFi settings. These include the Internet password, the Network name, and the security type. We suggest the use of WPA2 as the strongest form of security. Learn more in our How to Setup WiFi on the Dlink DAP-1555-Bridge-Mode guide.

Don't forget to sign up for NordVPN's promo deal before it's gone.

NordVPN faster than ever deal!

You might notice that most of our site doesn't have ads on it. This is because we use partnerships with companies like NordVPN to keep the site running. Thank you for supporting us by using our referral links.

Dlink DAP-1555-Bridge-Mode Help

Be sure to check out our other Dlink DAP-1555-Bridge-Mode info that you might be interested in.

This is the reset router guide for the Dlink DAP-1555-Bridge-Mode. We also have the following guides for the same router: